High Torque Servo Motor Sizing for 12V DC

Size a 12V DC servo motor for high torque; compare 24V and 48V.

Published ; reviewed .

12V DC high-torque servo sizing calculator

Wye PMSM + sinusoidal FOC only. RC/brushed: use supplier data.

Method, sources and limitations
Preparing interactive calculator…

Defaults and presets are hypothetical, not a motor specification. Replace the motor data below with a verified wye-connected, sinusoidal-FOC datasheet. All fields are required.

Required shaft torque, not a verified S1 motor rating. Range: 0.1–150.

Evaluated at the same speed; peak duration is not modelled. Range: 0.2–300.

Zero is allowed for holding torque. Range: 0–6000.

Before battery/source and DC cable voltage drop. Range: 9–120.

Motor, transmission and DC supply assumptions

Assumed efficiency: direct 100%; planetary 93% (≤10:1), 88% (>10:1); strain wave 75%. Verify the actual efficiency.

Fixed at 1 for direct drive. Range: 1–120.

Use the sinusoidal-FOC RMS convention, not peak or block-commutation Kt. Range: 0.001–10.

Wye motor: phase resistance = R line-to-line / 2. Range: 0.0001–20.

Use phase L, not line-to-line L; confirm the supplier’s conversion and mutual-inductance convention. Range: 0–100.

Electrical speed = mechanical speed × pole pairs. Range: 1–100.

A scenario input, not a predicted or permitted motor temperature. Range: -20–180.

Include BMS and source interconnects; 28 mΩ is an example only. Range: 0–2.

Both supply conductors plus contacts at operating temperature; excludes motor phases. Range: 0–2.

Voltage demand exceeds allowance

157.08 W output; motor 5 N·m at 300 RPM. Thermal and current ratings remain unverified.

Motor phase current (RMS)

12.5 / 30 A

Continuous / peak load. Not the DC supply current.

Required / available phase peak

6.9 / 6.2 V

Continuous headroom -11.3%; peak headroom -58.5%. Negative means unavailable.

Stator copper loss

24.65 W

At assumed 100°C; hot R line-to-line 0.1052 Ω. Hot Km 1.007 N·m/√W.

Requested DC source current

16.17 / 54.48 A

Continuous / peak demand; inverter bus 11.29 V; DC cable heat 4.08 W. No wire gauge recommendation.

Model limits

  • Continuous or peak voltage demand exceeds the linear SVPWM allowance. The requested point cannot be delivered under these assumptions.
  • Copper and bridge conduction losses only: iron, friction, switching losses, current ripple, motor-phase cable loss, magnetic saturation and auxiliary loads are omitted. DC power is an optimistic estimate.
  • No wire ampacity, motor thermal rating, peak duration, controller current limit, BMS cutoff or regenerative braking approval is provided.

Next steps

  • Try a lower torque or speed, compare a higher bus voltage, or obtain a winding matched to this operating point.
  • Send the motor datasheet and motion duty cycle for engineering review; verify DC wiring and connectors separately from motor-phase wiring.

Four decisions before choosing a 12V high-torque servo

Decision summary and evidence map
DecisionWhat to checkEvidence / limitation
Start with torque and speed togetherCompute phase current from the actual winding Kt, then check voltage at motor speed.maxon parameter conventions; formulas below. No universal current range follows from 12V alone.
Keep phase and DC current separateDrive current limits use the drive’s RMS/peak convention; source current follows input power.Power balance in Method; excludes unmodelled losses.
Higher voltage changes headroomThe same winding needs the same phase current for the same torque.TI BPRA073 voltage limit; fixed-winding comparison above.
Treat cooling and peak duration as open itemsRequest torque-speed/duty curves and installed thermal data.Siemens S3 duty guidance; no thermal approval from this tool.

Use the calculator to rule out incompatible electrical points before collecting quotes. A result within its voltage allowance still requires a motor/drive rating review. Motor parameter evidence, SVPWM evidence and duty-cycle evidence explain these checks.

Where this model applies

The model is for a balanced, wye-connected three-phase permanent-magnet motor under sinusoidal field-oriented control, with Ld = Lq and id = 0. Torque is assumed linear in phase RMS current. It supports motoring and zero-speed holding, not regeneration or braking. It does not model saturation, reluctance torque, field weakening or delta-connected windings.

Choose a compatible motor modelWye PMSM + sinusoidal FOCConfirm RMS Kt and phase LCheck load point and limits
Choose a compatible motor model. Conceptual process; not test data.

For a brushed DC motor, RC servo or integrated geared actuator, use its supplier’s output torque-speed and current data instead. If the winding convention is unknown, send the datasheet for review rather than treating the defaults as measurements.

Calculation method, units and assumptions

These are the page’s engineering derivations using the stated ideal motor assumptions. They are not supplier-certified performance predictions. maxon explains why commutation and parameter definitions matter.

Reproducible equations — RMS phase-current convention
QuantityEquationMeaning / boundary
Motor-side pointTm = Tout / (N ηg); nm = nout N; ωm = 2π nm / 60N is reduction ratio. Gear efficiency is an illustrative constant, including at zero speed.
Phase currentIcont = Tm,cont / Kt; Ipeak-load = Tm,peak / KtBoth values are phase RMS currents at two load points. Sinusoid crest = √2 × RMS.
Hot resistanceRll,hot = Rll,20 × [1 + 0.00393 (Tw − 20)]Copper approximation. Tw is user-assumed, not predicted.
Copper loss and KmPcu = 1.5 I² Rll,hot; Km = Kt / √(1.5 Rll,hot)Three phases, Rphase = Rll / 2. Thus Pcu = Tm² / Km².
Back-EMFEphase,pk = Kt ωm √2 / 3From Tω = 3 Ephase,rms Iphase,rms for this sinusoidal model.
Required voltageVreq,pk = hypot(Ephase,pk + √2 I Rll,hot / 2, ωe Lphase √2 I)ωe = pole pairs × ωm. Steady id = 0; ignores current slew and saturation.
Available voltageVallow,pk = 0.95 Vinverter / √3Linear SVPWM phase peak; 0.95 is our extra allowance.
DC equilibriumPinv = I_DC (Voc − I_DC Rloop)Rloop = source resistance + DC cable loop resistance. Use lower-current root; no root means unavailable.
Electrical input estimatePinv = Tout ωout / ηg + Pcu + 3 I² × 0.002 Ω2 mΩ hot MOSFET resistance is illustrative; omits switching, iron, mechanical and auxiliary losses.
Electrical screening calculationLoad → motor torque and speedKt, R, L → current and voltageDC sag → allowance and action
Electrical screening calculation. Conceptual process; not test data.

12V voltage headroom: compare like units

At an ideal 12V bus the linear SVPWM phase-peak ceiling is 6.93V; the equivalent line-to-line RMS ceiling is 8.49V. They describe different voltage conventions. The tool compares phase-peak demand with phase-peak allowance after source/cable drop and the 0.95 allowance. Peak torque is checked at the same entered speed, using its own supply sag. TI BPRA073, Figure 13.

Ideal inverter limits before losses or the 0.95 allowance
DC busPhase peak: Vdc / √3Line-to-line RMS: Vdc / √2
12V6.93V8.49V
24V13.86V16.97V
48V27.71V33.94V
Avoid a voltage convention mismatchDC bus at inverter terminalsLinear SVPWM: divide by √3Compare phase-peak demand
Avoid a voltage convention mismatch. Conceptual process; not test data.

Negative headroom rules out the point under these assumptions. Positive headroom is not a control-bandwidth guarantee. Field weakening requires a separate motor/drive analysis and cannot be assumed as a remedy.

12V vs 24V vs 48V: fixed winding and rewinding are different decisions

The interactive comparison keeps Kt, resistance, inductance, torque and speed fixed. Phase current and copper heating therefore remain equal across all three buses. DC current changes with input power and terminal voltage. Changing winding turns is a different comparison: Kt roughly scales with turns and resistance roughly with turns squared for a comparable copper fill. Saturation, end turns and manufacturability can invalidate that simple scaling.

What changes when voltage or winding changes?
ChangePhase current at equal torqueTrade-off
Higher bus, same windingUnchangedMore voltage headroom; verify drive, insulation and overvoltage limits.
More turns, same active geometryMay decrease as Kt risesHigher resistance and back-EMF; requires actual winding data.
Bigger motor / improved coolingDepends on winding KtCan improve continuous capability; increases envelope, mass or cooling cost.
Keep the comparison reproducibleSame load and same windingSame phase current and PcuDifferent DC current/headroom
Keep the comparison reproducible. Conceptual process; not test data.

Direct drive, planetary or strain wave: choose at the motor-side point

Transmission trade-offs — no universal backlash or life guarantee
ArchitectureBenefitCost or mismatch riskNext check
Direct driveNo gear backlash or gear frictionFull load torque at motor; larger motor/drive may be neededInstalled bearings, cogging, encoder and heat path
PlanetaryReduced motor-side torqueHigher motor speed; backlash, wear and gearbox costEfficiency vs speed/load, ratio, output bearing life
Strain waveCompact high reductionCompliance, friction, torque ripple and lifetime limitsRated moment, torsional stiffness and duty cycle

Illustrative tool efficiencies are 93% planetary up to 10:1, 88% above 10:1, and 75% strain wave. They are assumptions, not published product ratings. A reducer raises motor speed, so it can worsen voltage demand even while reducing motor torque. Direct drive still needs bearings and has finite component life.

Check the effect of a reducerOutput torque / (ratio × η)Motor speed = output × ratioRecheck back-EMF and losses
Check the effect of a reducer. Conceptual process; not test data.

Continuous torque, peak duration and cooling limits

A copper-loss estimate cannot establish S1 torque without a thermal path, cooling boundary and motor limits. The winding temperature field only sets resistance. It does not predict temperature rise. Use measured winding-to-housing resistance, housing-to-coolant conditions, time constants and sensor placement to assess the actual cycle.

For piecewise loads, RMS torque is √[Σ(Ti² Δti) / ΣΔti], subject to speed-dependent losses and peak limits. A 12 N·m pulse for 1 second followed by 3 N·m for 9 seconds gives √22.5 = 4.74 N·m RMS. That alone cannot approve the 12 N·m pulse. S3 denotes intermittent loaded/rest operation, not a fixed 3× peak multiplier. Siemens configuration guidance.

Thermal rating requires an installed motor modelDuty cycle and copper lossesThermal path + time constantsCheck winding and magnet limits
Thermal rating requires an installed motor model. Conceptual process; not test data.

Ask the supplier for magnet demagnetization limits and winding insulation limits for the selected assembly. A magnet grade name or insulation class alone does not guarantee an allowable operating temperature.

Request a winding and duty-cycle review

Source sag and wiring: separate the DC loop from the motor phases

The DC cable resistance input includes both supply conductors and contacts at operating temperature. A 1.5m one-way DC run has 3m of conductor in its loop. With a hypothetical loop resistance of 0.0156Ω and 20A DC, the drop is 0.312V and cable heat is 6.24W. These are resistance calculations, not an ampacity rating. Phase cables use phase RMS current and require a separate three-phase loss model.

The example source resistance of 0.028Ω is not a typical-value claim for all batteries. Use measured worst-case pack/BMS impedance at the relevant state of charge and temperature. Constant-power demand has a mathematical limit Voc² / (4 Rloop); a practical source usually imposes current and undervoltage limits earlier.

DC path and motor phases carry different currentsSource + BMS: average DCTwo-wire DC loop → inverterThree motor phases: RMS AC
DC path and motor phases carry different currents. Conceptual process; not test data.

No AWG is recommended. Verify ampacity, insulation, bundling, fault protection and connector ratings using the actual installation. Reduce resistance, load or cable length when supply-limited; increasing wire size alone cannot fix a motor voltage mismatch.

Drive, encoder and braking integration

Match drive continuous phase RMS and allowed transient crest current to the same convention used by the winding datasheet. A quoted DC current limit is not interchangeable. The tool assumes 2mΩ hot MOSFET resistance and includes conduction only; driver switching loss, DC-link capacitor ripple and phase-cable loss remain open items. TI’s reference design illustrates why current capability belongs to specified voltage, cooling and control conditions.

At low speed, encoder quantization and velocity estimation affect smoothness. Compare counts per mechanical revolution, absolute accuracy, latency and observer filtering rather than imposing a universal minimum bit depth. Validate a direct-drive joint with the actual controller and load inertia.

Braking or lowering a load can return energy to the DC link. Provide a verified regenerative path, brake resistor or source that accepts energy. A suspended load also needs a separate load-holding assessment; this motoring calculator does not size a safety brake.

Three worked examples you can reproduce

All examples below are hypothetical calculations, not measured customer outcomes or product performance claims.

Hand-check examples with explicit assumptions
Scenario and assumptionsCalculationDecision / remaining limit
Direct drive: 5 N·m, 300 RPM, Kt 0.4 N·m/A RMS; Rll 0.08Ω at 20°C; winding 100°CI = 12.5A; hot Rll = 0.105152Ω; Pcu = 24.645W; output = 157.08W; Ephase,pk = 5.924VDefault 12V case needs more loaded voltage allowance, especially at peak. Check the result and 24/48V comparison.
Geared: 6 N·m at 150 RPM; 10:1 planetary, η = 0.93; Kt 0.05Motor = 0.6452 N·m at 1500 RPM; I = 12.90A RMSReduced motor torque does not prove speed feasibility. Use the AGV preset to check voltage and peak demand.
Holding: 5 N·m at 0 RPM; Kt 0.4; same hot Rll as the first exampleMechanical power = 0W; phase current = 12.5A RMS; copper loss = 24.645WZero speed still heats the winding. Check stall-current conventions, thermal limits and holding safety.
Turn a worked example into a real selectionReproduce the arithmeticReplace hypothetical motor dataValidate torque-speed and duty
Turn a worked example into a real selection. Conceptual process; not test data.

What is known, assumed and still required for procurement

Evidence status before requesting a quote
ItemStatus on this pageMinimum next step
Electrical equations and unitsDefined and reproducible under stated modelConfirm wye and sinusoidal FOC conventions
Motor Kt, R, L and pole pairsHypothetical defaults; user-editableRequest winding-specific datasheet and tolerances
Motor diameter, bore and torque ratingsUnknown — no verified SKU specification hereRequest outline, CAD, winding and installed torque-speed data
Continuous/peak duration and thermal capabilityUnknownSupply cooling interface and motion-time profile
Drive, wiring and BMS capabilityUnknownVerify current, voltage, protection and installed temperature ratings
Price, delivery and CAD turnaroundNot quotedConfirm scope and delivery timing with engineering

A smaller geared motor can add gearbox cost, maintenance and compliance. Direct drive can increase motor, inverter and cooling costs. Compare the complete installed system against the required motion performance. Browse CAD resources and the datasheet library; confirm that any downloaded file matches the selected winding and model.

Primary sources and claim boundaries

Sources checked 2026-11-08. Publication dates below belong to the referenced documents; the review date does not imply a new edition. Formulas, example resistances, gearbox efficiencies and the 0.95 voltage allowance are explicitly stated page assumptions or derivations.

maxon — Motor data and simulation

Updated 2024-08-29

Explains torque/current constants, motor constant and temperature dependence. It explicitly distinguishes block commutation from sinusoidal FOC parameters.

Scope: Supports the need to check parameter conventions; it does not validate any example motor or thermal rating on this page.

Texas Instruments — BPRA073: Field Orientated Control of 3-Phase AC-Motors

February 1998; section 5.3 and Figure 13

Defines the linear SVPWM voltage circle, whose phase-peak radius is Vdc / √3.

Scope: Our additional 0.95 multiplier is a screening allowance, not a TI guarantee. Device drops, dead time and controller limits can reduce output further.

Texas Instruments — TIDA-010056 reference design

Product overview checked 2026-11-08

Documents a 54 V / 1.5 kW power stage and 25 A RMS continuous operation under its stated test conditions.

Scope: Its trapezoidal-control results are not a 12 V sinusoidal-FOC rating and do not transfer to an arbitrary inverter.

Siemens — 1FW6 built-in torque motors configuration manual

September 2022; section 6.2, intermittent duty S3

Describes S3 as repeating loaded and unpowered rest intervals, with RMS current and thermal time constraints.

Scope: S3 is a duty designation, not a universal peak-torque multiplier or a permitted acceleration duration.

High-torque servo selection FAQ

12V selection and motor data

Can a 12V DC servo motor deliver high torque?

Yes at a suitable speed with a matched winding, drive and cooling arrangement. Voltage alone does not specify torque. Use Kt to estimate phase current and check the loaded torque-speed curve.

Is this calculator for an RC servo or a brushed motor?

It models a balanced wye-connected three-phase PMSM with sinusoidal FOC and zero d-axis current. RC integrated servos, brushed DC motors, delta connections, IPMSM saliency and six-step commutation need their own models.

Can I use the example motor data for an order?

No. Defaults and presets are hypothetical. Obtain the actual winding Kt in N·m per phase RMS ampere, line-to-line resistance, phase inductance, pole pairs and torque-speed curve before selection.

What if my Kt is specified per peak ampere?

For a sinusoidal phase-current convention, Kt per RMS ampere equals √2 times Kt per peak ampere. Confirm the supplier uses this definition; a DC-input or block-commutation Kt cannot be converted by this rule alone.

Current, voltage and supply

Does changing a 12V supply to 48V reduce motor phase current?

For the same winding and torque, Iphase = T / Kt is unchanged. Higher voltage can reduce average DC input current and increase speed headroom. A different winding changes Kt and resistance and requires a fresh calculation.

What voltage is available from a 12V inverter?

Ideal linear SVPWM allows 12 / √3 = 6.93 V phase peak, equivalent to 8.49 V line-to-line RMS. This tool uses 95% of the phase-peak allowance after DC source and cable sag.

Why are DC current and phase current different?

PWM transfers power between the DC link and three motor phases. Phase current sets torque; average DC input current follows the electrical input power and DC terminal voltage. They can differ greatly at low speed or stall.

What does supply-limited mean?

The continuous or peak electrical demand has no stable lower-current equilibrium in the specified resistive source model. Real BMS cutoff or current limiting can happen sooner. Reduce demand or resistance and check source ratings.

Does voltage-limited mean the motor is damaged?

It means the requested operating point exceeds this model’s linear voltage allowance. It is not a damage prediction. Reduce torque or speed, evaluate a higher bus, or ask for a matched winding and drive.

Will a gearbox always fix a 12V voltage problem?

No. Gearing reduces motor torque but raises motor speed. With a fixed winding, back-EMF and inductive voltage demand can rise. Check the entire motor-side operating point and gearbox efficiency.

Heat, wiring and practical next steps

Is S3 the same as peak torque?

No. S3 describes intermittent periodic loaded/rest duty. A motor’s allowed peak torque and duration depend on its magnetic, drive and transient thermal limits. Use the supplier’s curves and the actual motion cycle.

Does the tool predict winding temperature?

No. Winding temperature is an input used to adjust copper resistance. The tool cannot infer cooling capability without mounting conditions and a measured thermal model.

Can I use the result to select a wire gauge?

No. Enter measured or calculated DC loop resistance for voltage drop only. Ampacity needs conductor insulation, ambient temperature, bundling, connectors, protection and installation requirements. Motor-phase cables require a separate check.

Can the calculator evaluate holding torque at zero RPM?

Yes, but it assumes sinusoidal RMS phase currents and omits PWM ripple. Copper losses remain at zero mechanical power. Verify the drive’s stall-current convention, cooling and load-holding safety separately.

Why is my peak request checked at the operating speed?

No acceleration trajectory is supplied, so peak torque is conservatively evaluated at the entered speed as a separate steady point. Duration, inertia, current slew and regeneration remain unmodelled.

What should I send for engineering review?

Send the motor winding datasheet, continuous and peak output torque, speed-time duty cycle, supply min/max voltage, source and cable resistance, envelope, cooling interface, encoder and braking requirements.

Review the winding and duty cycle before ordering

Share torque, speed, supply limits, motor data, cooling and envelope constraints. Engineering can confirm the required information and review scope, including CAD availability and timing.